Extreme Networks Summit WM Series Guia do Utilizador Página 100
- Página / 228
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
WM Access Domain Configuration
Summit WM-Series WLAN Switch and Altitude Access Point Software Version 1.0 User Guide
100
Set up Wi-Fi Protected Access privacy (WPA) for an AAA WM-AD
1 To set up WPA privacy on the WM-AD, click on the WPA radio button.
2 To enable either WPA v1 or WPA v2, or both, click the appropriate checkboxes on.
3 To enable re-keying after a time interval, click the Broadcast re-key interval checkbox on (the default
is on). Type in the re-key time interval (the time after which the broadcast encryption key is changed
automatically) in seconds.
If the box is unchecked, the Broadcast encryption key is never changed and the Altitude AP will
always use the same broadcast key for Broadcast/Multicast transmissions. Note that this reduces the
level of security for wireless communications.
4 To save the privacy parameters for the new WM-AD, click on the Save button.
A WM-AD with no authentication
You can choose to set up a WM-AD that will bypass all authentication mechanisms and run Summit
WM-Series Switch Software with no authentication of a wireless device user.
On such a WM-AD, however, you can still control network access with filtering rules. See “The non-
authenticated filter for Captive Portal” on page 87 for information on how to set up filtering rules that
allow access only to specified IP addresses and ports.
Set up a WM-AD with no authentication
1 In the WM Access Domain Configuration screen, highlight the WM-AD name in the left-hand list and
click on the Top ol og y tab.
2 In the Top olo gy screen, select Network Assignment by SSID. Follow the steps described above for a
WM-AD for Captive Portal. Save the new WM-AD Topology by clicking on the Save button.
3 Click on the Authentication tab for this WM-AD. Click on the Configure Captive Portal button.
4 In the Configure Captive Portal subscreen, select the No Captive Portal radio button, for no
authentication on this WM-AD, then click on the Save button.
- Table of Contents 3
- Formatting conventions 10
- Documentation feedback 10
- Protocols and standards 11
- Regulatory information 11
- About this Guide 12
- Conventional wireless LANS 13
- Wireless AP 15
- Summit WM 15
- Wireless Controller 15
- Network traffic flow 18
- Network security 19
- Policy: packet filtering 21
- Mobility and roaming 21
- Availability 22
- Quality of Service (QoS) 22
- Data ports (4 or 2) 24
- Management ports 24
- Configuration steps: overview 31
- Enabling the product key 31
- Setting up the data ports 32
- Port Type or Function 34
- Setting up static routes 35
- Setting up OSPF Routing 36
- Define port exception filters 40
- 4 Altitude AP: startup 41
- Installing the Altitude APs 43
- Set the discovery timers 45
- Discovery and registration 46
- Registration after discovery 48
- Altitude AP access approval 49
- ● 802.11 b/g (2.4 GHz radio) 53
- ● 802.11a (5 GHz radio) 53
- Adding a Altitude AP manually 56
- Auto Cell software 58
- Configure Auto Cell software 59
- Altitude AP: startup 60
- Introduction 61
- What is a WM-AD? 62
- Topology of a WM-AD 62
- Filtering for a WM-AD 64
- Setting up a new WM-AD 66
- Global Settings for a WM-AD 68
- Topology for a WM-AD 71
- Use DHCP Relay for the WM-AD 74
- Topology for a WM-AD for AAA 75
- Authentication for a WM-AD 76
- ● No Captive Portal Support 80
- Captive Portal” on page 87) 81
- Accounting for a WM-AD 84
- RADIUS Policy for a WM-AD 84
- Filtering rules for a WM-AD 86
- Default Filter: Examples 93
- Multicast for a WM-AD 95
- Privacy for a WM-AD 96
- Privacy for a WM-AD for AAA 97
- A WM-AD for voice traffic 101
- Availability and Mobility 103
- Management users 111
- Network time 112
- Check Point event logging 113
- Setting up SNMP 115
- Setting SNMP Parameters 116
- Overview 123
- Summit Spy: running scans 125
- The Analysis Engine 126
- 11 Ongoing operation 131
- Altitude AP client management 133
- Client disassociate 134
- Client blacklist 135
- Health Checking 136
- Change the system log level 136
- Enable and configure Syslog 136
- Logs and alarms 141
- View the Logs 142
- View the Traces 142
- View the Audits 143
- Reports and displays 144
- View reports 146
- Glossary 147
- D (Continued) 149
- F (Continued) 151
- H (Continued) 152
- I (Continued) 153
- O (Continued) 156
- P (Continued) 157
- S (Continued) 160
- T (Continued) 162
- W (Continued) 164
- Altitude AP system states 168
- B CLI command reference 169
- CLI command reference 170
- RFC list 177
- 802.11 standards list 178
- Reference lists of standards 180
- E Support for Altitude AP 181
- F RADIUS Attributes 183
- RADIUS Accounting 184
- Account-Stop/Interim Packet 185
- Termination Codes 186
- G Logs and Events 187
- Logs and Events 188
- Critical 189
- CDR_COLLECTOR 191
- CONFIG_MANAGER 191
- EVENT_SERVER 192
- RADIUS_ACCOUNTING 194
- RADIUS_CLIENT 194
- RF_DATA_COLLECTOR 195
- RU_MANAGER 195
- SECURITY_MANAGER 196
- STARTUP_MANAGER 197
- STATS_SERVER 198
- ACCESSPOINT 200
- CPDP_AGENT_ID 203
- NSM_SERVER 205
- OSPF_SERVER 206
- PORT_INFO_J_MANAGER 206
- REDIR_ID 207
- H Regulatory Information 213
- Emissions 214
- FCC ID#: RJF-A3502 216
- Part 15 Unlicensed Antenna 217
- European Community 218
- European Spectrum Usage Rules 221
- Regulatory Information 222
- Declarations of Conformity 223
Manuais e produtos relacionados com Software Extreme Networks Summit WM Series
Software Extreme Networks WM20 Controller Especificações
(170 páginas)
(170 páginas)
Software Extreme Networks Ridgeline Guide Especificações
(376 páginas)
(376 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais